電動卷簾門相比起傳統的卷簾門來說，減去了繁瑣的開鎖和拉門過程，十分適合現代人的使用。電動卷簾門安裝、使用和維修過程中有許多的注意事項，許多人對此往往知之甚少，濟南卷簾門小編就將為大家介紹一下這些注意事項，從而供大家有需要的時候做下參考。

Compared with the traditional roller shutter door, the electric roller shutter door reduces the tedious process of unlocking and sliding the door, and is very suitable for modern people. There are many precautions in the installation, use and maintenance of electric roller shutter doors, which many people often know little about. The Jinan roller shutter door editor will introduce these precautions for you, so as to provide you with reference when you need them.

安裝注意事項

Installation precautions

電動卷簾門安裝位置的上端應有可靠的防火設施，在卷簾門的卷筒下端做包箱或吊頂時須設置可拆式活動蓋板，在電動卷門機一側下端須預留500×500mm可拆檢修孔，以便于維修保養。

Reliable fire protection facilities shall be provided at the upper end of the installation position of the electric roller shutter door. When the lower end of the drum of the roller shutter door is used as a packing box or ceiling, a detachable movable cover plate shall be provided, and 500 mm shall be reserved at the lower end of the side of the electric roller shutter door × 500mm removable manhole for easy maintenance.

所有電動控制的卷簾門，啟閉運行方向須與開關箱指示相同，特別是在新接通電源試車或外來輸入電源變換相線時，應先使用手動裝置將門簾置于門洞高度1/2的位置，接通電源后試操作卷門啟閉，直到與指示相附，方可正常使用，否則損壞限位器，引起卷簾反卷或沖頂?shù)榷斐蓳p失。

The opening and closing direction of all electrically controlled roller shutter doors shall be the same as that indicated by the switch box. In particular, when the power supply is newly connected for trial run or the external input power is used to change the phase line, the manual device shall be used first to place the door shutter at the position of 1 / 2 of the door opening height. After the power supply is connected, the roller shutter shall be opened and closed for trial operation until it is attached with the indication. Otherwise, the stopper will be damaged, causing the roller shutter to reverse roll or flush, causing losses.

操作注意事項

Operating precautions

電動卷簾門操作時，操作者須站在能看到卷門運行狀態的位置進行操作，否則易發生意外而受損。

During the operation of the electric roller shutter door, the operator must stand at the position where the operation state of the roller shutter door can be seen, otherwise it is easy to be damaged by accident.

電動卷簾門門簾和卷門機禁止與酸、堿性物溶液接觸，以防腐蝕門簾表面。

The electric roller shutter door curtain and the roller shutter machine shall not be in contact with acid and alkaline solutions to prevent corrosion of the door curtain surface.

卷門機在運行、滑行、傳動等部位應定期檢查(少每年2次)，并根據需要及時加油，以保證卷簾門的正常使用。

The rolling door machine shall be regularly inspected (at least twice a year) during operation, sliding, transmission and other parts, and timely refueled as required to ensure the normal use of the rolling door.

電動卷簾門在啟閉停止過程中，應具備隨位停止之功能，不應有停止而繼續下滑現象，如發生下滑距離大于50mm的情況出現，應立即對卷簾門控制電器和卷門機制動器進行仔細檢查修理，運行正常為止。

In the process of opening and closing, the electric roller shutter door shall have the function of following the position, and shall not stop and continue to slide. If the sliding distance is greater than 50mm, the control electric appliance of the roller shutter door and the roller shutter mechanism shall be carefully inspected and repaired immediately until the operation is normal.

維修注意事項

Maintenance precautions

電動卷簾門門簾和易銹部位，應進行定期防腐、油漆及保養處理，禁止用重物、硬物沖擊門面。

The electric roller shutter door curtain and rust prone parts shall be subject to regular anti-corrosion, paint and maintenance treatment. It is prohibited to impact the door surface with heavy objects and hard objects.

電動卷簾門運行時如有發生較大抖動或異常聲音時應停機檢查，排除有礙門簾正常啟閉的雜物。

In case of large shaking or abnormal sound during the operation of the electric roller shutter door, stop the machine for inspection to eliminate the sundries that hinder the normal opening and closing of the door shutter.

電動卷簾門底梁座上限位置須與軸承架下端保持大于200mm的距離，以確保制動停止時不發生沖頂現象。

The upper limit position of the bottom beam seat of the electric roller shutter door must be kept at a distance of more than 200mm from the lower end of the bearing frame to ensure that there is no rush when the brake stops.

通過上文的介紹，我們已經大致了解了電動卷簾門安裝、使用、維修過程中的注意事項。從中我們可以看到，電動卷簾門安裝時要注意各個部位的連接緊密，再投入使用前要反復檢查，避免使用過程中再出現些什么問題。更多相關事項就來我們網站http://www.kwy6.cn咨詢了解吧。

Through the above introduction, we have generally understood the precautions during the installation, use and maintenance of the electric roller shutter door. We can see from the above that during the installation of the electric roller shutter door, attention should be paid to the tight connection of all parts, and repeated inspection should be conducted before putting it into use to avoid any problems in the process of use. For more information, please visit our website http://www.kwy6.cn Consult and understand.