車庫門在我們的日常生活中，車庫門的遙控器很少壞，有些只是丟失了密碼，有些只是沒電了。如果遙控器丟了，那就沒辦法了，所以，我們只能更換它。如果是丟失了密碼，我們需要知道如何編碼車庫遙控器。下面濟南卷簾門廠家為您講講。

Garage door in our daily life, the remote control of garage door rarely breaks, some just lose their passwords, and some just run out of power. If the remote control is lost, there is no way, so we can only replace it. If we lose our password, we need to know how to code the garage remote control. Now let's talk about Jinan roller shutter factory.

1.目前車庫門遙控器主要與車庫門無線連接，一般采用固定編碼或滾動編碼。由于每個的車庫門遙控器的編碼不同，獲得它的比較簡單方法是咨詢制造商。但一般市場上車庫門遙控器的頻率為433.92mhz或315MHz。遙控器一般有三個鍵，但也有兩個鍵;

1. At present, the garage door remote controller is mainly wirelessly connected with the garage door, and generally adopts fixed coding or rolling coding. Since the codes of garage door remote controllers of each brand are different, the relatively simple way to obtain them is to consult the manufacturer. However, the frequency of garage door remote control in the general market is 433.92mhz or 315MHz. The remote controller usually has three keys, but there are also two keys;

2.準備遙控器進行代碼匹配，按下開門器的代碼匹配鍵，該鍵通常在電機后面，按住1-2秒，指示燈變?yōu)槌Ａ?。按遙控器按鍵，遙控器上的紅燈和開門器上的紅燈同時亮，按2-4次(開門器的不同次數)，兩個紅燈同時亮2-4次，即碼匹配成功;

2. First, prepare the remote control for code matching, press the code matching key of the door opener, which is usually behind the motor, press and hold for 1-2 seconds, and the indicator light will turn on. Press the button on the remote control, and the red light on the remote control and the red light on the door opener will be on at the same time. Press 2-4 times (different times of the door opener), and the two red lights will be on at the same time for 2-4 times, that is, the code matching is successful;

3.代碼匹配過程完成后，指示燈應熄滅。如果此時碼匹配指示燈一直亮著，則表示仍處于碼匹配狀態，很可能配備了其他遙控器，導致將來自動開門關門造成不必要的損失。因此，代碼匹配完成后，一定要按代碼匹配鍵退出;

3. After the code matching process is completed, the indicator light should be off. If the code matching indicator is always on at this time, it means that it is still in the code matching state, and it is likely to be equipped with other remote controls, resulting in unnecessary losses caused by automatic door opening and closing in the future. Therefore, after the code matching is completed, be sure to press the code matching key to exit;

以上是車庫門遙控器編碼的具體操作步驟，希望它能幫助您。當然在平常生活中還是要對車庫門多加維護和保養，這樣才能讓其使用的更好更長久，更多咨詢了解就來我們網站http://www.kwy6.cn關注吧。

The above is the specific operation steps of garage door remote control coding. I hope it can help you. Of course, in daily life, we still need to maintain the garage door more, so that it can be used better and longer. For more information, please come to our website http://www.kwy6.cn Pay attention.